30
Oct
To ensure proper thread engagement and accurate torque readings clean ALL threads in the block. Want to check a torque or stretch value.
Then install the nuts onto the studs and thread by hand down until the nut contacts the washer.
Arp main stud torque specs. This is information that you can never find when you need it so here is a table for the ARP Head. First lets be clear. ARP provides torque specs for our fasteners based on using ARP Ultra-Torque.
If youre not using our specs and our lube you have no real idea what pre-load youre getting. Weve done the testing where we can measure the torque applied and the resulting pre-loads. ARP General Torque recommendations.
Apply ARP Ultra-Torque to fastener threads and the underhead of the bolt or underside of the nut. Install fastener hand tight. Use torque wrench to install fastener to the torque value from the chart below.
The torque values represented here are intended. What are the ARP Bolt Torque Specifications. Rod bolts with part no.
BEB-08 BEB-09 BEB-14 BEB-15 and BEB 19 need 65 foot-pounds of torque if you are. Tighten fly wheel bolts with part numbers FBB716 FBT716 and FBV8716 with 90 foot-pounds of torque. The specifications listed below with ARP ULTRA-TORQUE FASTENER ASSEMBLY LUBRICANT.
Inner studs - 4770 long 60 ft lbs M8 side bolts 20 ft lbs use RTV sealant under the head of bolt Outer studs - 4550 long 50 ft lbs Windage tray nuts 28 ft lbs. Lost your kit instructions. Want to check a torque or stretch value.
Enter your kit number in the field below and click Submit Important. If you have an aftermarket connecting rod with an ARP bolt please use the chart below to contact the rod manufacturer for the stretchtorque value. The calculation of those values is solely up to the rod manufacturer.
ARP consistently strives to exceed industry specifications for quality and product management. MS bolt specifications cover a wide range of fastener hardware high strength bolts nuts and washers with specs for materials and processing. MS fasteners have various tensile strengths.
Ford 62L V8 Cam Drive Bolt Kit. Ford 62L V8 Main Stud Kit. BB Ford V8 hex Intake Manifold Bolt Kit.
BB Ford V8 12pt Intake Manifold Bolt Kit. Ford Motorsport M6010 Boss 302 wrear sump oil pan. SB Ford 351 2-bolt.
SB Ford 351W 2-bolt. SB Ford 302 wdual or rear sump oil pan. Chevrolet Gen V 62L LT1LT2 8740 hex.
Timing Cover Bolt Kit. Chevrolet Gen V 62L LT1LT2 8740 12pt. Timing Cover Bolt Kit.
Chevrolet Gen V 62L LT1LT2 ARP Stainless hex. Timing Cover Bolt Kit. Chevrolet Gen V 62L LT1LT2 ARP Stainless 12pt.
Timing Cover Bolt Kit. Pontiac 400-455 4-bolt Main Stud Kit. SB GM 2100 OD Seal Plate Specialty Kit.
Pontiac 350-400 hex Intake Manifold Bolt Kit. Automotive Racing Products Tel. 805 339-2200 1863 Eastman Avenue.
Fax 805 650-0742 Ventura Ca. To ensure proper thread engagement and accurate torque readings clean ALL threads in the block. Duramax 66L L5P Head Stud Kit ARP-supported Speed Demon 715 Sets New Land Speed Record NEW KIT.
Aftermarket Axle full thread thread-in 12pt 12-20 x 1950 UHL. Outer Main Cap Bolt. Inner Main Cap Bolt.
Outer Main Cap Bolt. ARP MAIN B18BB16B17B18C Following the manufacturers recommended torque sequence tighten the nuts in three equal steps to 30ft lbs60ft lbs and then 80ft lbs with ARP ULTRA-TORQUE FASTENER ASSEMBLY LUBRICANT. Head Stud and washer mounting locations 1-8 in torque sequence M11 X 5050 in.
Washer 9-10 in torque sequence M11 X 5150 in. Washer 11-15 in torque sequence M8 X 2725 in. Lubricate the stud threads and bottom of the nuts with ARP Ultra-Torque Fastener Assembly Lubricant.
Then install the nuts onto the studs and thread by hand down until the nut contacts the washer. Following the manufacturers recommended torque sequence shown below use a 14mm socket to torque the nuts per steps 1-3.