15
Sep
When this is done heat the casting around the broken bleeder really hot with a torch and remove the offending bleeder with the allan wrench you drove into it. Also any advice on removing the broken valve is appreciated.
If the bleeder is broken flush with the housing you will have to cut into the housing a small amount.
Broken brake bleeder valve. Showing the real world removal of a broken brake bleeder screw and what happens all too often with a screw extractor. Videos dont always go as planned and sometimes broken bleeders dont come out of the caliper as planned. For instance in this videos a bit of heat and pound.
Theoretically the broken bleeder valve should be still tight it is the conical tip deep inside the caliper that seals the brake Assuming the valve did not move when you broke it. Practice a pressure test so you can see if the valve is still sealing. Use a hacksaw to cut a screw slot in the top of the broken bleeder as in Figure 381.
If the bleeder is broken flush with the housing you will have to cut into the housing a small amount. This portion of the casting is a non-structural part and if done properly this will not harm the caliper. Sportster Models - Broken Bleeder Valve 2009 Iron 883 - Hey yall.
This is my first post. I have a 2009 Iron 883 XL883N So I was just refilling my brake fluid after replacing my brake line and reverting my master cylinder to stock position after it had been in chainsikle rearsets. Everything had gone well until I.
Soak the stuck bleeder with penetrating oil overnight if possible. Spray the penetrating oil on the area beside the threads and also through the middle of the bleeder. Attempt to remove the bleeder using a six sided socket of the appropriate size.
Do not use a wrench of a twelve point socket. I am driving a 2013 Porsche Cayenne two local shops Sears auto center Mavis Discount Tire flushed my brake fluid in past 4 years. One of them snap off one of my passenger side rear caliper valve strews head.
I noticed last month and decided to extract the screw by myself. I bought the WD-40 and screw extractor from home depot but it could not pull the remaining screw out. I tried to.
Dont apply brute force to the bleeder screw Step 1. Pin the bleeder valveKeep in mind that the brake bleeder valve is hollow. So any force you apply to it with a.
Cut off excess rod and apply rust penetrant. I was trying to bleed my brakes after replacing brake line but my bleeder valve broke off in my rear caliper. I want to replace it with a speed bleeder but I cant find the depth spec anywhere.
I know it is m8x125. Also any advice on removing the broken valve is appreciated. This wrench must fit really tight if you cant find a tight fit measure the flats of the next size bigger allan wrench and drill the bleeder this size and broach the wrench into the hole.
When this is done heat the casting around the broken bleeder really hot with a torch and remove the offending bleeder with the allan wrench you drove into it. Your brake bleeder screw or bleeder valve is located on the back of your calipers or wheel cylinders and allows air and old brake fluid to be purged from the brake system. When opened it allows the brakes to be bled and when closed seals the system and brake fluid.
If your bleeder screw is damaged corroded or wont seal they can usually be replaced. Dorman offers a line of brake bleeder repair kits to repair stripped-out bleeder screws on a caliper. All our brake bleeder repair kits are constructed of high-quality materials for long-lasting durability.
Effectively restores brake function Save money by repairing the bleeder screwsinstead of purchasing an entirely new brake caliper. If the bleed valve is broken then it is necessary to replace it with a new one. Obtain a blowtorch and gently heat the valve for approximately 13 seconds.
Pass the torch from one side to the other to heat it evenly. Put the caliper in a bowl of cold water and leave it in for a few seconds. Brake Proportioning Valve Bleeder Tool - EGSTAOR Valve Bleeding Tool Compatible with GM Combination Valves PV2 PV4 DiscDisc DiscDrum AC Delco 172-1353 172-1371 990 9.
90 Get it as soon as Tue Jan 26. Acouto 08-0143 Motorcycle Hydraulic Brake Bleeder Discharge Device Tool Clutch Brake Bleeder Hose One Way Valve Tube Bleeding Tool Kit. 44 out of 5 stars 3.
8 coupon applied at checkout Save 8 with coupon. Get it as soon as Tue Jan 12. FREE Shipping on orders over 25 shipped by Amazon.
You then slide the bleeder-screw-sized impact socket onto the end of the tool. Place the air hammer and Brake Free tool onto the potentially always stuck rusty bleeder screw. Crank up the air hammer and then spin the Brake Free with a 34 wrench.
Order Brake Bleeder Tools for your vehicle and pick it up in storemake your purchase find a store near you and get directions. Your order may be eligible for Ship to Home and shipping is free on all online orders of 3500. Check here for special coupons and promotions.
An incorrect bleeder screw a burr on the bleeder or in the caliper orifice or a crack in the caliper are about all there could be to cause the problem and a close inspection of the bleeder screw and orifice should make the defect obvious.