22
Nov
The valve cover sealing surface is checked with a straight edge to be sure the cover is flat and thus reusable. If its shiny with oil then you can be pretty certain your valve cover gaskets need replacing.
Unbolt the bolts that hold the valve cover down with a 14 inch 06 cm drive ratchet.
How to replace valve cover gasket. Professional and fast replacement of valve cover gasketsHow to replace a valve cover gasket. Get here a step-by-step practical tutorial by seal professional. The first step may be the last step.
Before tearing everything apart first try gently cinching down the valve. Allow the engine to cool. Consult the service manual or instructions for valve cover removal.
Lift off the valve cover. Tapping with a rubber. Pull all wires and vacuum hoses away from the valve cover top.
Make sure to remember where all of the hoses and vacuum hoses were connected. Some people like to snap a picture. Unbolt the bolts that hold the valve cover down with a 14 inch 06 cm drive ratchet.
Inspect the bottom of the valve cover at the rear. If its shiny with oil then you can be pretty certain your valve cover gaskets need replacing. However if it feels like your valve cover bolts.
Peel off the old valve cover gasket. Clean the area where the new gasket is going on. With your finger rub the valve cover gasket with petroleum oil to lubricate it.
This helps the gasket to slide a bit when you are putting the valve cover into place. This protects the gasket from tearing. Put the new valve cover gasket in the valve cover.
The replacement cost of a valve cover gasket will be between 90 and 350. The parts cost will be anywhere from 40 to 50 while the labor costs will be anywhere from 50 to 300. As you can see this is not a very expensive part to replace in your vehicle.
The extent of the expense will be based on the hourly rate of your mechanic. How do mechanics replace a valve cover gasket. Some engines have plastic covers over the entire top.
The plastic engine cover is removed to access the valve covers. A valve cover gasket kit part cost 20-65. How much does the valve cover gasket replacement cost.
In a simple in-line 4-cylinder engine the valve cover gasket replacement may cost 90-175 parts and labor. In a Subaru boxer engine with two separate valve covers a dealer or repair shop may charge 145-360 for parts and labor. Replacement of the valve cover gasket involves moving out of the way whatever wiring harnesses or obstructions there are.
Sometimes removing coils or spark plug wires then unbolting and removing the cover. The valve cover sits atop the cylinder head and the valve cover gasket is sandwiched between them to keep circulating oil inside. The majority of valve cover gaskets are molded rubber tailored to fit.
In some cases the spark plug tube gaskets are part of the valve cover gasket and are replaced at the same time. Valve cover gaskets are. Using a rubber mallet tap the sides of the valve cover.
You can also use your hands. Keep wiggling back and forth until the VC pops off. – the old gasket material is acting like a glue - so you may want to get a thing razor blade in between the seem and cut some old RTV loose.
Pull the valve cover straight up and this is what you should see. To get to the valve cover and the gasket the mechanic may have to remove the intake. This large section of the car will be secured with clamps but these can be loosened with a screwdriver.
The solenoid will also have to removed. The mechanic may be able to unplug it but in most cases they will need to unbolt it. Peel off the old gasket and clean the valve cover with brake cleaner and clean rags.
Next clean the gasket mating surfaces on the engine. Use the plastic putty knife never metal to remove any traces of old RTV from the timing belt cover-to-cylinder head. Catch the old RTV with a rag so it doesnt fall into the engine.
The Valvetronic motor gasket and Valvetronic sensor seal can be replaced once the valve cover is installed. This makes things much easier later on and prevents inadvertently damaging the seals particularly the Valvetronic sensor seal. For now remove the Valvetronic motor seal by undoing the two T30 screws.
Step 11 - The cover gasket will either be stuck on the cylinder head or the valve cover itself remove the old gasket. Remove Valve Cover Gasket Step 12 - Using a shop towel and some carburetor cleaner wipe the gasket surface clean to ensure a proper reseal of the new gasket. Once the valve covers is accessed the cover retaining bolts are removed and the cover pulled off.
The valve cover sealing surface is checked with a straight edge to be sure the cover is flat and thus reusable. The new valve cover gasket is applied along with new rubber grommets under the retaining bolt heads. The valve cover sits atop the cylinder head and the valve cover gasket is sandwiched between them to keep circulating oil inside.
The majority of valve cover gaskets are molded rubber tailored to fit. In some cases the spark plug tube gaskets are part of the valve cover gasket and are replaced at the same time. Valve cover gaskets are.