24
Jul
Tighten the diagonal lower intake manifold bolts two on each end to 7 Nm 62 lb in. Gen VI Big Block Chevy Engine Specs.
Tighten the diagonal lower intake manifold bolts two on each end to 7 Nm 62 lb in.
Intake manifold torque specs chevy 350. In the GM 350-cubic-inch engine the intake manifold bolts to the cylinder head with 33 foot-pounds of torque. The intake manifold supplies this engines eight cylinders. Small Block Chevy Intake Manifold Bolt Torque Specifications 25 FtLbs Make sure you follow the sequence in a couple of steps worry about this more on old and aluminum manifolds.
Cast Iron is much more forgiving if you are unfortunate to have to use a boat anchor of an intake. Torque Specifications for GM 57L-350ci-V8. Bell Housing To Engine Block.
When torqueing the intake manifold on these engines you need to two-step the torque following the bolt pattern in the image above to a maximum of 35 lb-ft. If youre rebuilding a 57-liter Hemi Below this is reduced to a single pass at nine lb-ft of torque. Intakes are kind of funny when it comes to torque specs.
According to my Chevrolet Factory Performance Guide the specs call for 30 ft. Of torque working from the center bolts in a. The Edelbrock Performer EPS 2701 intake manifold has been designed for 262-400 cid.
Small-block Chevy engines operating in the idle to 5500 rpm range. The manifold accepts late model water neck air conditioning alternator and HEI. Use electric or manual type choke standard flange carburetors only.
These specs are for stock-type bolts with light engine oil applied to the threads and the. Chevy Silverado Air Filters and Intake Manifolds Edit categories Edit Intake Torque specs on 98 350 Vortec The 98 Vortec 350 CID engine has an aluminum intake and a plastic plenum mounted to it. I just had to tear mine down due to a blown intake manifold gasket on the water port located above 1 Piston.
This caused MAJOR leak of Anti. The torque specification is a 2-step process. Tighten the vertical lower intake manifold bolts the four middle ones to 7 Nm 62 lb in.
Tighten the diagonal lower intake manifold bolts two on each end to 7 Nm 62 lb in. Tighten the vertical lower intake manifold bolts the four middle ones to 13 Nm 115 lb in. The Chevrolet 350 cylinder-head torque specification is 65 ft-lbs.
The intake installed onto cast-iron heads requires 30 ft-lbs. If your engine has aluminum cylinder heads the threads are more fragile than the cast iron so the intake specification is 18 ft-lbs. Torque sequence used for tightening a carbed intake manifold.
Chevy SB shown on this videoDisclaimer. To the best of my knowledge this video is accurate. Intake manifold-50L and 57L engines.
Intake manifold bolt tightening sequence-1988-95 50L and 57L engines. Access our GM Full-Size Trucks 1988-1998 Lower Intake Manifold Repair Guide Removal and Installation by creating an account or signing into your AutoZone Rewards account. I have a Gen 1 Chevy 350 in my 76 Monte.
I have removed the stock heads and put on vortec heads. I am putting a GM vortec intake manifold on as well. Im not sure how old the vortec heads or manifold is but I think they came from a ZZ Crate engine.
Anyone have any idea what the torque specs are in foot-pounds for the manifold. Intake manifold design is geared toward the end usage whether that is a street performance engine or an all-out competition application. The wide range of Chevrolet Performance intake manifolds means there is an ideal manifold for your many needs.
There are cast-iron and aluminum intake manifolds for carbureted and fuel injected applications. Specifications additional parts that you may need to purchase torque specifications and a service parts list. The 350 HO engine incorporates modern technology in a package that can be installed in applications where 265-400ci small block Chevrolet V-8s were originally used.
GM Engine Torque Specs. Torque Sequence and Specs. Small Block Chevy Vortec Intake.
Small Block Chevy Engine Specs. Gen VI Big Block Chevy Engine Specs. Subscribe for Exclusive Offers.
Get Exclusive Online Offers. Size USE TORQUE Lubricant. 38 - 16 Intake manifold 25 lb.
Water Outlet 20 lb. Exhaust manifold 25 lb. Aluminum aftermarket heads and intake manifolds require a different torque than stock cast iron units.