07
Jul
When engine oil service is due the Time For Service warning light will appear on the display. Your Saab expert will be able pinpoint the problem for you by connecting your Saab to a diagnostic scan tool.
In some cases you need to pull over immediately to prevent damage while in others you merely need to tighten you gas cap next time you stop in order to reset the service engine soon light.
Saab check engine light reset. The quick and dirty way is to pull fuse 17 out of the fuse box drink a glass of iced tea and then put the fuse back. This will reset the engine management system and cause the CEL to go off. The fuse box is behind a panel at the end of the dash on the drivers side.
In some cars especially those made before the mid-1990s you can reset the check engine light by disconnecting the battery. Newer vehicles have a feature that will simply turn the light back on after the battery is reconnected if the car is not drained of electricity properly however. A check engine light can indicate a broad spectrum of problems with your 2004 Saab 9-3.
In some cases you need to pull over immediately to prevent damage while in others you merely need to tighten you gas cap next time you stop in order to reset the service engine soon light. The video above shows how to locate the on board diagnostics OBD plug on your 2004 9-3 how to read the trouble codes and how to reset or clear the check engine light using a scanner on your 9-3. With a check engine light on the first thing you need to find out is what caused it.
You can either take your car to the workshop for a full diagnosis or read the fault codes with an OBD-II scanner. Fix the underlying problem and reset the codes. These devices come at all shapes sizes and prices to choose from.
There are three ways to reset a check engine light. Disconnect the battery wait approximately 30 minutes reconnect the battery. This resets the cars computer which also reset the check engine light.
On newer OBD on-board diagnostic compliant vehicles this usually does not work. About Press Copyright Contact us Creators Advertise Developers Terms Privacy Policy Safety How YouTube works Test new features Press Copyright Contact us Creators. Using a scan tool is the easiest way for check engine light reset.
If you wonder to know how to turn off check engine light by this way here are 3 steps for you. Connect the scan tool to the OBD II Connecting the scan tool to the OBD- II On- board diagnostic connector under your steering column. You may also need to manually reset the light after making repairs if the code doesnt clear automatically.
The best way to reset a check engine light is to use a code scanner. However if your vehicle was manufactured before 1996 you can simply disconnect the battery to reset the light. Your Saab expert will be able pinpoint the problem for you by connecting your Saab to a diagnostic scan tool.
This tool will provide trouble codes stored in your electronic control system and reveal why the check engine light came on. From there your Saab specialist will advise you on what to do next for your Saab and recommend a proper course of action. 2007-2011 Saab 9-3 Time For Service Minder Light Reset Time needed.
When engine oil service is due the Time For Service warning light will appear on the display. The service interval must be reset after performed the maintenance service or change the engine oil on your vehicle. The reset check engine lights process takes an extra step on modern cars.
Before the deployment of OBD II in 1996 resetting a check engine light was a simple matter. Just disconnect the battery for more than 10 seconds and youre done. You could even pull the electronic control module fuse on many models.
After the engine was torn down and repaired the check engine light kicks on every 400 to 1000 miles. They have replaced the rings computer throttle body twice air box and other smaller items. By the way each time this happens the engine goes into limp mode and doesnt go above thirty miles an hour.
The average cost for a Saab 9-3 check engine light diagnosis testing is between 143 and 180. Labor costs are estimated between 143 and 180. Estimate does not include taxes and fees.
The cost of this service or repair can vary by location your vehicles make and model and even your engine type. Related repairs may also. Turn the ignition switch to the Drive position without starting the engine.
In about six seconds the CHECK ENGINE light will go out for about 2 seconds. It will then begin flashing the first fault code. The codes consist of a number of flashes each having a duration of 04 seconds.
Or reset check engine light airbag light inspection key or insp errors when maint reqd for Saab cars. Or any warning light for service reminder which appears on the display. Write in the search box the car name for which you want to find information and find how to reset other service reminders by yourself.